How to Replace a Tub Yourself: Removing and also Replacing.
How to Replace a Tub Yourself: Removing and also Replacing.
Blog Article
Almost everyone has their unique rationale when it comes to Tools You Need to Install a New Bathtub .
Mounting a tub isn't precisely rocket science, however it does require strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately tough project. If the old bathtub is readily obtainable, the project can move speedily; if you need to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the job is much harder. In either instance, the project is within a house handyman's skills, although you will certainly require a helper to vacate the old tub as well as set in the new one. See to it you have certified yourself for the task and also are comfortable trying it. Rather than employing a contractor to take over a halfway-completed task, it is better to think about using one before you start. Chances are you may need a specialist plumber to make tube connections.
This post will certainly help you set up a brand-new bathtub in your shower room if you have actually already purchased a brand-new bathtub and don't require to transform the arrangement of your previous water system pipelines.
Your tools as well as product list should make up the following:
Getting ready for the Installment
To start with, the supporting framework provided with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When fitting the tap block, it is essential to make certain that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop pressure on the bathtub.
Fit the flexible tap connectors to the bottom of the two taps utilizing 2 nuts as well as olives (often provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which must be fitted inside the bathroom. Make certain you utilize all of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a comparable manner.The bathroom must now be ready to be fitted in its last placement.
Removing Old Touches
If you require to replace old taps with new ones as a part of your installment, after that the first thing you must do is detach the supply of water. After doing so, turn on the taps to drain pipes any kind of water staying in the system. The procedure of eliminating the existing taps can be fairly bothersome because of the restricted access that is often the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric ready for the remaining water that will originate from the pipes. Once the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to quit the single taps from transforming during this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Before going on to fit the brand-new taps, contrast the pipe links on the old taps to the brand-new faucets. If the old taps are longer than the brand-new taps, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Utilizing the two wood boards under its feet, place the bath tub in the required placement. The wooden boards are helpful in equally spreading the weight of the bath tub over the area of the boards as opposed to focusing all the weight onto 4 little factors.
The next objective is to make sure that the bathtub is leveled all round. This can be accomplished by checking the level and changing the feet on the bathtub up until the spirit level checks out degree.
To set up faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipeline by making a compression join; after that do the same for the various other tap.
Turn on the water supply as well as examine all joints and brand-new pipework for leaks as well as tighten them if essential. Fill the bath tub and likewise examine the overflow outlet as well as the regular outlet for leakages.
Ultimately, repair the bathroom paneling as described in the producer's user's manual. Tiling and sealing around the bath tub should wait up until the bath tub has been utilized at the very least once as this will settle it into its last position.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to stop damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will need lowering couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, place the tap in the installing opening in the bath/basin ensuring that the washers remain in area between the tap and also the sink. Safeguard the tap in position with the supplier provided backnut. When the faucet is firmly in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap ports. The previous type ought to be linked to the faucet finishes initially, tightening only by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and also the tiling, bring about complications with wetness and also feasible leaks to the ceiling below.
You can choose from a variety of coloured sealants to blend in your fixtures and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a larger gap to load, you can load it with spins of drenched paper or soft rope. Keep in mind to constantly fill up the tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture relatively early if you do not consider this movement prior to securing.
Additionally, ceramic coving or quadrant tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily offered on the market. It is advisable to fit the tiles making use of waterproof or water resistant sticky and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate more info about A Step-by-Step Guide to Installing a Bathtub? Leave feedback down below. We'd be delighted to find out your responses about this blog entry. In hopes that you come back again later on. Don't hesitate to set aside a second to share this blog post if you enjoyed reading it. We cherish reading our article about Installing A Bathtub.
Learn More Report this page